n00b question, sorry. If I had a desktop that could hold 4 HD and 2 SSD, could I turn it into a NAS? Could someone point me in the right direction if this makes sense?
Yep. Just install Linux, plug it into your router, set a static ip, and install the nas software ya want.
There are plenty of approaches. ChatGPT is great at debugging issues and helping ya through the setup. I did this with a raspberry pi and external usb drive the other week.
Nice, didn’t realize a NAS could be on smaller hardware. Thanks for the info!
Some people even use Raspberry Pis as their NAS. I use an old MacBook (5th gen i5) as a home server with 2 external hard drives as a NAS, which also runs a few docker containers like Jellyfin. Before that, I was using an old PC with 1st gen i3 for all these things.
It’ll work fine. A NAS is just a PC. Try Unraid if you want a user friendly UI. It costs money but it’s only a one off payment for a lifetime license, and they have a free trial.
Or truenas
+1 for unRAID. I did the same when I got tired of Netflix increasing prices while dropping content. Also got annoyed with my cable because it’s expensive and good content is rare.
Bought a 12th gen i5 desktop on sale and 4 x 10Tb drives and installed unRAID on a USB key.
Easiest thing I’ve done in years and it’s 100x better than Netflix and 1000x better than cable.
yes, try freenas/truenas
You totally can, but since it will be on all day with 4 hdd look into wattages you want to live with. There are some small NUCs or Pi based NAS with low wattages. There is OpenMediaVault, FreeNAS/TrueNAS software to install
Hey sorry, thinking on this more, could I just turn on the NAS when desired? What is the benefit of running it constantly?
Yep, look into Wake On LAN if you just want to power the NAS on remotely.
My NAS also powers on at certaIn times of day and off again after a while - IF - no-one’s connected / no network traffic / etc.
I do NOT need my NAS on at 3am…
Edit : forgot to say, check out OpenMediaVault
deleted by creator
Stellar! Thanks for the info!
You can also configure the HDDs to power down when they’re not in use. HDDs are the biggest power consumer anyway.
Note that there is some reliability drawback of spinning hard disks on and off repeatedly. maybe unintuitively HDDs that spin constantly can live much longer than those that spend 90% of their time spun down.
This might not be relevant if you use only SSDs, and might never affect you, but it should be mentioned.
You could totally turn on as needed, WakeOnLan is good for that. But typically when people run a NAS it is for streaming audio, video, file sync and backups and maybe docker running other services so the NAS is typically on 24/7 so it is available on demand. But it doean’t have to be 100% uptime if you don’t want it to be. For example I have two OpenMediaVaults one on a pi and one an old IomegaNAS. The pi is on always with an attached drive, and serves Samba Shares and DLNA/DAAP shares. Has docker running syncthing, CUPS print server, Trillium Notes, and homeassistant; so makes sense for it to be on all day, especially because my wife’s system backsup to it daily automatically. The converted Iomega NAS is mainly a backup machine sInce it is old and not as performant (only has 100 network speed. So that gets turned on to do a bulk backup and not much else.
Nice, good things to balance. Thanks for the info!
Yes. Go look at TrueNAS Scale
Just google perfect media server
Of course. Just put disks in and set up whatever remote filesystem and it’s a NAS.
Thanks!
My NAS is just a very old Acer desktop from like 2011. I bought a Fractal Meshify 2 case which can hold I think 14 hard drives and moved the internals into that. Works great.
Eventually I had to get a pcie card for more data ports, and replace the power supply with one that’s more than 300w.
My first NAS was an old desktop that I got for $300 running an FX-6300 and a GTX 550, I slapped a couple hard drives in there, installed Ubuntu, and made an SMB share.
I’d recommend installing TrueNAS Scale on a system rather than doing what I did in part due to it being so much better than what I was doing, but you could run it on a potato if you wanted.
Hell my latest NAS upgrade is going from a PowerEdge T610 (tower server from like 2010ish) running TrueNAS Scale to a normal desktop (from 2017) running TrueNAS Scale
If anything using normal desktop hardware makes servicing it easier than using old server hardware
Unraid as I understand it will do that
Saving for later
Absolutely anything can be turned into a NAS, as long as you’re aware of your own needs and the hardware’s capabilities. A NAS is just a computer with some specific requirements.
When I first built my NAS, it only used parts that I got for free. A cheap micro ATX board with only two RAM slots, an i3-4160 CPU, 2x2G RAM, a worn-out SSD, and a 1T HDD. It couldn’t run something like TrueNAS, but it was enough for Proxmox and some Alpine containers running services like Samba, Transmission, Wireguard, and a small Debian VM for me to fuck around with. The single storage disk means there is no redundancy, so I only store replaceable data on it, like TV shows and installers.
There are many hardware-focused channels on video platforms that offer guides for budget home servers. Wolfgang’s Channel is good, and Hardware Haven and Raid Owl just finished a competition of building a sub-$200 home lab.
deleted by creator
i’d avoid BIOS-based RAID… it doesn’t really offer many benefits over linux-based raid like MDADM, and MDADM offers a LOT of up-sides for portability, repairability, diagnostics, etc
BIOS RAID tends to be the worst of both worlds, it’s not real hardware RAID and it’s not as flexible as full software RAID.
My NAS is an mATX mobo with an i5, 64G RAM, 8 disk drives, 3 nvme drives, and an ARC GPU for video transcoding.
Disk drives are all mirrored. One nvme runs NixOS which is easy enough to redeploy if the drive dies. One nvme is cache on top of the disk drives. Last nvme I use for temp fast storage like Jellyfin transcoding.
Its more of a combo NAS/server as I run most self hosted apps on it (tor node, monero node, jellyfin, *arr stack, etc).
I just got an arc for jellyfin transcoding. Could you tell me more about your setup for that?